Low Cost DIY Front Door Refresh

Having a red front door is a must for any house I live in. It’s bright, warm and welcoming. Now our front door is a 1973 original and it was more than just a little blah. I have thought about a total replacement but doors are expensive and hard to in stall.

Now lets look back, the front door was a dusty red, with a horrendous paint job. The hardware was worn bronze with patina starting to show up. I finally decided to repaint the door and replace the hardware with a more modern black matte finish set. I wanted to accomplish this little renovation on a budget.

Here’s what I used:

Rust-Oleum Painter’s Touch – Gloss Apple Red for $8.27

Belleview Venetian Bronze Single Cylinder Door Handleset –  $93.00

Project total = $101.27

Similar new doors can cost upwards of $600! This front door refresh is a nice alternative for a fraction of the cost!

“I really liked being the girl behind the red door.” – Brooke Davis One Tree Hill

I am not going to lie, the handle was pretty hard to install, not because of the complexity but rather because of the door itself. The door is old and the handle didn’t fit perfectly at first. I had to break out the drill to expand some of the pre-cut holes to allow for the new hardware.

Spring Theme Table Setting with Napkin Fold How-To!

Okay I think y’all know that I am more than excited about Spring! Finally my home and table setting fits the changing season too! I wanted to make a setting that was a little more unqiue and has a vintage flair to it! I love to mix it up! Also I had to say goodbye to the little vintage bunny in the picture, who ever gets him in their March box…his name is Fred. Take good care of him! Ha!

What you need:

  1. Traditional napkin
  2. Decorative carrot (I got my at my local Homegoods, the whole package was $14.99)
  3. Vintage books — These can vary in cost but these are two that I had on hand – extra vintage brownie points if they are Spring themed or children’s books
  4. Round straw style placemat
  5. Farmhouse Style napkin or in my case I used tea towels
  6. Plate

Get the look:

  1. Place the placemat at the bottle
  2. On top of placement place an attractive plate
  3. Place the vintage book open on the plate
  4. Top with napkin with carrot tucked inside (Steps to the napkin fold I used below!)

How to tucked carrot fold:

Fold your napkin in half

And half again

Take the top corner and fold diagonally. Do this two more times, tucking the triangles in as you go. Make sure you leave a little showing each time.

Fold the right side of the square behind

Flip the napkin and fold the left side in

And wa-la! Gorgeous! Now just tuck that carrot in and enjoy this setting!

The Work Begins at the good Ol’ Chicken Farm

ISap9xmifgvym81000000000.jpg

It took my mother a total of 64 years of life before she could purchase her very first home, and it is everything she has ever wanted it to be. A rural farmhouse atop a hill that makes your ears pop as you ascend. Her neighbors are dairy farms, apple orchards and pumpkin patches which leaves her with endless excitement. Just 3 weeks after completing Chemotherapy and her second round of cancer treatment in the last 15 years, she is totally ready to take on the challenges of renovating a 1700s farmhouse.

20171018_130631.jpg

Yesterday we decided it was time to pull down the drop ceiling in what used to be the kitchen, and yes we wondered what could possibly possess a person to put a drop ceiling in an antique home. Well we found out. Midway through my pulling down of the tiles with a crowbar, which I only maimed myself with a little, I found lovely old water damage on the underlying sheetrock. Previous owners had a leak at some point, and while they repaired the cause of the leak they never repaired the underlying damage! They simply put in drop ceiling to conceal it! Talk about a bandaid for a bullet wound!

20171018_142555.jpg

This type of lazy repair work is pretty common in older homes, they have had many years of owners ill-equiped to take on the projects that come in general homeownership let alone the responsibilities of owning an antique home. Any renovation lover can tell of the pain it is to walk around antique homes and see the damage inflicted by previous owners, and how it can take a lot of work to backtrack what has been done.

 

We still have our work cut out for us, 3 more rooms with drop ceilings, moving of plumbing and electrical,  plus replacement of exterior clapboards and windows that have been rotted by water from missing gutters. Keep tuned in as we dig into this antique and get it ready for Grandma D to call it home.

Quick and Dirty Bench Recover DIY

In my dining room we have a lovely 150-year-old library table built by my husbands great-grandfather. It’s solid Oak and absolutely gorgeous, however there are no matching chairs. Last fall, prior to my daughter’s arrival we realized that we really need to have more than two chairs. I bought a beige bench from Nebraska Furniture Mart in The Colony, TX and it was a perfect fit, but it did not wear well. With two large pups, a baby and lots of visitors a year later the bench is looking pretty rough.

20170921_141248 (1).jpg

See the big stain!? Not sure if that is baby or fur-baby related! So it was definitely time to recover this bad boy, but I am certainly not a professional at this. However I can wield a staple gun and a pair of scissors with a moderate amount of skill.

After making a trip to Hobby Lobby I found some upholstery fabric for $6.00 per yard, bought two yards and I was on my way! Note here, I wouldn’t try covering an piece of upholsterted furniture with anything other than upholstery fabric, it just won’t wear as well.

Getting Started 

Now in the title I note that this was a quick and dirty job, I didn’t measure twice and measure once again for good practice. I had limited time before I would relieve my mother-in-law from baby duty and had to get cracking. I knew that I wouldn’t have tons of fabric left over, but I had more than I needed. I laid the fabric over the bench and tried to make sure it was even on all sides, and that the geometric pattern was lined up with the edges. If was crooked it would look very odd.

Start with the Ends

I flipped the bench up so I could see the underside and pull the fabric tight. Eyeballing it I determined I didn’t need all the fabric on the end so I cut the extra and stapled the remaining in to place. Once the end was material was fixed to the underside of the bench  I folded the fabric and created a pleat that ran down to the leg and pulled it around, stapling it so the material remained tight.

 

And Again on the Other End

I repeated the same procedure on the opposite end of bench, remembering to use the same pattern for tucking, pleating and wrapping the material around the leg. If you don’t do this, it will be strange and bug you. Or at least it would drive me nuts not be symetrical.

20170921_142858

On to the Sides

At this point I flipped the bench upside-down, trimmed the excess material and stapled the fabric along the underside of the bench, while making sure there was no slack. This whole process took less than 15 minutes and didn’t require anything more that a staple gun and a pair of scissors. I didn’t measure, remove anything or take anything apart. Plus the whole replacement cost me a whopping $12

20170921_143839.jpg

DIY Fireplace makeover

 

IMG_20170826_174456_680

Oh what to to do with a fireplace with outdated tile that doesn’t match your style or color scheme at all? If it’s brick, easy, white wash it and enjoy the new lighter tones. But tile does present its own challenge. In our case, our new house has faux marble tile surrounded by a gorgeous hearth. I knew I wanted to cover it with a look that was a little more chic and feminie but I wasn’t sure what.

IS2fcm9zogrldr0000000000

The Photo above shows what we were starting with (a photo that I was able to steal from the listing from when we purchased the house). Bland walls that allowed the amazing hearth blend in and drew the eye to the earth toned marble tile. So first thing first we spruced the walls by adding a fresh coat of Sherwin Williams Wet Pavement paint to add contrast between the walls and trim, while also allowing for a cooler color pallet that I tend to favor.

20170826_114354

Step One: Tape and Prime

This is a really important step, I love the way my hearth looks in white so I wanted to make sure a did a really good job taping off the edges. Because tile is very tricky to paint, as it is a glossy smooth surface, you need to start with a primer that will give the paint a surface to stick to. If you weren’t to do this it would get very streaky and probably start peeling immediately.

I used a small 4-inch roller (my new favorite thing) to apply Zinsser Cover Stain – Primer-Stain Blocker and Bond Coat. I did multiple coats until I was happy with the texture and cover and let it dry for a couple hours. Bone-headed moment warning — I typically set up fans when painting to get rid of the nasty smell (especially when using a strong primer). However I decied to point my fan directly the fire place, which of course stirred soot everywhere. Including the freshly primed surfaces. This was a 15 minute delay as I had to quickly remove the soot and repaint the effected areas. So please do not point fans directly at the fireplace while working!

Step 2: Painting

I utilized the same 4-inch roller to apply white semi-gloss paint to the entire surface of the tile, waited for it to dry and applied a second coat. At his point the next step is taping off for the stripes, which means the underlying white needs to be COMPLETELY dry before applying the tape. This is incredibly important, if the white paint is still tacky, the tape when removed will pull at the paint and primer and you will make a mess that requires a lot of touch up.

Step 3: Stripes!

20170826_143015

I measured the width of the painters tape, I so happened to buy, at 1 3/4 inches and used that as the spacing. Starting with the very bottom, I placed the bottom pieces flush against the corner of the angle, making sure that the tape was long enough to extend beyond the painting surface. Measuring up from there, I used a sharpie to mark every 1 3/4 inches. Once the marks were made, I applied the tape every other space all the way up in the most level manner possible. After each tape placement I verified with a small level that they were even.

Step 4: More Painting

20170826_144045

Next using a combonation of a small foam paint brush and 4-inch roller I applied the black paint to the spaces inbetween the tape. This was tricky as it was easy to see streaks of white through the black. In total there was at least 2-3 coats of black paint and inbetween each I allowed them to dry a little, this helped prevent additional streaking.

Once the black was done I allowed it to partially dry. Now this may be up to some debate but I like to remove my painters tape before the paint is completely dry, this prevents the paint pulling up when it’s removed. However if you do it too soon, and the paint is too wet you can get dripping or smudges.

Step 5: Touch ups

Inevitably there will be some bleeding or smudging along the way. But resist the urge to try to touch it up immediately. Wait until the black dries completely then using a small foam brush or other paint brush touch up the errors. With waiting until the paint is completely dry, you avoid mixing paints that may still be wet and getting odd gray tones.

TA-DA the finished product!

 

Powered by WordPress.com.

Up ↑